The unit does not appear to operate correctly! The unit has been dropped or the enclosure damaged. The user should not attempt to service the equipment. All service work is done by a qualified service technician.
Exposure to extremely high noise levels may cause a permanent hearing gloss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U. Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure exceeds the limits set forth above.
To ensure against potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
As an example in the United Kingdom the cable colour code for connections are as follows. NOTE This manual has been written for easy access of information. The front and rear panels are graphically illustrated, with each control and feature numbered. For a description of the function of each control feature, simply check the number with the explanations adjacent to each panel.
Your Laney amplifier has undergone a thorough two stage, pre-delivery inspection, involving actual play testing. When you first receive your Laney Bass amp, follow these simple procedures: i Ensure that the amplifier is the correct voltage for the country it is to be used in. Please retain your original carton and packaging so in the unlikely event that some time in the future your amplifier should require servicing you will be able to return it to your dealer securely packed.
Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment.
At the same time we believe we have not lost sight of the reason Laney was founded in the first place - a dedication to building great sounding amplification for working musicians. On the rear is an FX loop for connection of external FX, a dedicated output for a tuner and two external speaker sockets for connecting cabinets.
An explanation of these features follows on pages High output basses, either Active or Passive should be connected via the High socket. Low output basses should be connected using the normal input.
High output basses may also be placed in the Normal input if pre-amp overloading is desired. This control is used to set the level of gain present in the pre-amp. The higher the level of gain, the more the signal will clip producing distortion. The Gain control should be used in conjunction with the Volume control to produce the desired signal characteristics.
Engages and disengages the on-board compressor, this compresses the input-signal giving a punchier sound. In association with the compressor are two LEDs, one indicating that the compressor is engaged and one indicating the compressor is active. The amount of compression is controlled by the Gain control. The higher the setting the more compression. With most guitars compression will begin at about on the control. It is possible to have the compressor engaged but it only be active during certain periods of playing - typically the most dynamic sections.
The Enhance control provides an increased definition at the low-end of the frequency spectrum giving you a tighter, punchier sound. The Enhance control does this by providing a dip in the frequency-response of the amplifier at approximately Hz. This dip reduces some of the harmonics of the important low-frequencies around Hz producing better definition to your sound.
Turning the control through to its maximum has the effect of boosting both the low and high-frequency content. There are seven sliders covering a frequency range from 40Hz right through to 6KHz. When the slider is in the central position the signal at that frequency is unaffected or flat. Moving the slider up or down from the centre will Boost or Cut that frequency.
Allows the on-board limiter to be defeated if desired. With the switch in the out position the limiter is engaged. The limiter is automatically triggered at high-output levels and is designed to prevent power-amp distortion at high-output levels. When the limiter is automatically triggered the LED lights up to indicate the limiter is active.
It is possible to have the limiter engaged but not have the LED active. The limiter monitors both power-amp clipping and speaker load so it automatically registers the cabinet-impedance and sets itself accordingly. Sets the overall listening level of the amplifier. XLR socket for direct-injection of the amplifier signal to a mixing-desk or additional power-amplifier. The XLR socket 10 provides a balanced low-impedance output-signal from the pre-amplifier taken before any tone correction.
Power inlet socket. Connect to your power source. Good luck to the repair! Please do not offer the downloaded file for sell only use it for personal usage! Looking for similar laney manual? Document preview [1st page]. Please tick the box below to get download link:. For this no need registration. Please take a look at the below related repair forum topics.
May be help you to repair. If you are not familiar with electronics, do not attempt to repair! You could suffer a fatal electrical shock! Instead, contact your nearest service center! Translate this page:.
Laney CVA aktiv hangfal impedancia illesztes?! Sziasztok Jott a baratom egy aktivhangfallal, hogy nem szol tobbe. Elso nekifutasbol "megbrummogtattam" a bemenetet nem volt keznel kabel , semmi hang nem volt, de feltunt, hogy ha felhuzom a hangerot mikozben a bemenet meleg pontjat erintem, akkor a huto ventillator felporog. Szetszedtem, beleneztem. Elkeserito volt amit lattam.
En egy kovetkezo kovetkeztetesre jutottam, kivancsi vagyok, kinek mi a velemenye.
0コメント